Generic

Piaggio Vespa Kinetic 38.4mm Stock Piston Kit - 12mm Wrist Pin

Replacement 38.4mm piston kit with 12mm wrist pin. Works with Kinetic and Vespa Piaggio mopeds.  Attention!  You must remove your cylinder and see what size wrist pin you have.  10mm...

Piaggio Vespa Points Ignition Coil

Points ignition coil for Vespa, Piaggio, Ciao, Grande, Bravo, Kinetic mopeds with points ignition systems. Will work with Puch Maxi Points ignitions as well. Mounting hole distance is 52mm center to...

Piston Wrist Pin Bearing, 12 x 15 x 15

Wrist pin bearing for the crankshaft connecting rod, commonly referred to as the con rod. 12x15x15 12=ID 15 =OD 15 =Width This bearing will fit: Tomos A35, A55, Puch, some Vespa and Peugeots, and...

Plastic Push In 33mm Gas Cap, Non Vented - Peugeot / Vespa

Push in non vented gas cap. For 32-33mm tank openings. Fits Peugeot 103 and Piaggio ciao. * Be sure to measure. *Must clean bung before installingThis is 31mm and then 33mm on the ridges.

Polyurethane Oil Injection Line / Hose, 2.2mm *by the foot* - Green

Translucent green polyurethane oil injection line for mopeds and many smaller motorcycles, such as Garelli, Puch Magnum, and Tomos. Can also be used for the air injection on your intake or...

Polyurethane Oil Injection Line / Hose, 3mm *by the foot* - Solid Green

Solid green polyurethane oil injection line for mopeds and many smaller motorcycles, such as Garelli, Puch Magnum, and Tomos. Can also be used for the air injection on your intake or carburetors...

Puch "maxi" Tank Decal Set - Chrome

Replacement Puch "maxi" tank decal set, one decal for each side. Could be used on any other Puch as well.Actual decal dimensions are 210mm Long by 28mm Wide.

Puch 11mm Loose Front Axle Assembly - No Ball Bearings

Replacement 11mm loose bearing axle for Puch mopeds. 155mm LongIncludes:AxleAxle nutsBearing racesCone nutsWashers

Puch 12mm Loose Rear Axle Assembly - No Ball Bearings

Replacement 12mm loose bearing axle for Puch mopeds. 212mm LongIncludes:AxleAxle nutsBearing racesCone nutsWashers

Puch 15mm Intake for Bing Carburetors - Polished

15mm intake for Puch Maxi, Newport, Magnum and similar mopeds Puch based engines.Works with stock carburetor or 15mm for increased air flow.Square port* Polished for better air flowDimensions:15mm O...

Puch 15mm Intake for Bing Carburetors - Square Port

Square port 15mm intake for Puch Maxi, Newport, Magnum and similar mopeds Puch based engines.Works with stock carburetor or 15mm for increased air flow.Dimensions:15mm O.D.20mm O.D.8mm Thick...

Puch 17" 5 Star Mag Wheel, White - Bare

New reproduction Five Star  mag rim. Typically found on Puch mopeds.  Now in White. Only the bare wheel is included and need the corresponding hubs linked below. Sold each. Buy two for a...

Puch 19mm OD Intake for SHA Carburetors - Sqaure Port

19mm intake for Puch mopeds. This will fit the  SHA Carburetors.Dimensions:38mm eye to eye 19mm OD 14mm ID Recommended Accessories:  Intake Gasket 

Puch 5 Star Mag Wheel - Fluorescent Green

New Flo green 5 star mag wheel for Puch mopedsOnly the bare wheel is included and need the corresponding hubs linked below. Sold each. Buy two for a pair and save $ Dimensions: 17" Diameter1.35"...

Puch 5 Star Mag Wheel - Fluorescent Yellow

New Flo yellow 5 star mag wheel for Puch mopedsOnly the bare wheel is included and need the corresponding hubs linked below. Sold each. Buy two for a pair. ;) Dimensions: 17" Diameter1.35"...

Puch 5 Star Mag Wheel - Gloss Black

New gloss black 5 star mag wheel. Only the bare wheel is included. Dimensions: 17" Diameter1.35" Width Recommended Accessories:5 star front hub assembly5 star rear hub assembly

Puch 5 star Mag Wheel, Bare - Gloss Dark Grey

Replacement gloss grey 5 star mag wheel for Puch mopedsThese are a darker grey than the original Grimeca grey. The picture lightened them up a bit, but they are absolutely darker than NOS. Only the...

Puch 5 Star Wheel Front Hub with Bearings / Spacer, Ver 1

Puch 5 star mag wheel  replacement hub with sealed (2) 6001 ZZ bearings and a spacer. This is version has a dull finish. For use with 12mm axle Dimensions:Spacer / Bushing: 36mm L x 17mm OD x...

Puch 5 Star Wheel Front Hub with Bearings / Spacer, Ver. 2

Puch 5 star mag wheel  replacement hub with sealed (2) 6001 bearings and a spacer. This is version has a polished finish. For use with 12mm axle Dimensions:Spacer / Bushing: 36mm L x 17mm OD x...

Puch 5 Star Wheel Rear Hub with Bearings / Spacer.

Puch 5 star mag wheel  replacement rear hub with sealed (2) 6001 ZZ bearings and a spacer. For use with 12mm axle Dimensions:Spacer / Bushing: 36mm L x 17mm OD x 13mm ID80mm brake...

Puch 6 Block Electric Wire Connector Terminal, Small - Black

Replacement electrical wire terminal block as found on Puch powered moped like the Maxi, Magnum, Newport, etc.. One wire in each end and the current is transfered accross for easy connections. These...

Puch 70cc AJH Reed Valve Gasket Pair

Quality reed gasket set for the AJH cylinder kit. Includes: (2) Reed gaskets only.    Recommended Accessories: Puch 70cc AJH Cylinder kit

Puch 70cc AJH Reed Valve Gasket Set

Quality gasket set for the AJH cylinder kit. Includes: Intake, base, head, and exhaust gaskets.   Recommended Accessories: Puch 70cc AJH Cylinder kit

Puch Adjustable Racing Clutch - 3 Shoe

Adjustable 3 shoe racing clutch for Puch E50 powered mopeds. No woodruff key needed. Threaded holes for clutch puller tools, makes installation and removal that much easier.*Not high...

Puch Bing Metal Mesh High Flow Air Filter

Chrome metal mesh high flow air filter made for  for Puch Bing Style Carburetors with 20mm clamp on filter area (12mm, 14mm and 15mm sized carbs)*May or may not fit under your side...

Puch Carburetor Rebuild kit, Bing 12mm/15mm - Round

A rebuild kit for round Bing 12 and 15 millimeter carburetors.Great option for those who want to rebuild rather than buy a replacement.These carburetors were found on most Puch powered mopeds like...

Puch Center Stand Mount Bracket w/ Hardware

Replacement Puch center stand mount assembly, includes mounting hardware and spacer. Will fit E50 and ZA50 models. *Includes 3 bolts for E50. ZA50 would need another bolt, Not included.*

Puch E50 12V CDI Stator, Magneto, Box with Spark Wire / Boot

12 volt CDI package for Puch e50 powered mopeds. Cloned from Bosch Ducati style Ignitions.*Looks to be a quality kit, but be sure to check everything before final assembly and pick up the regulator...

Puch E50 Bearings and Seal Set - 4 Bearings / 3 Seals

Bearings and seals set for rebuilding Puch E50 powered mopeds. Includes:(x3) 6203 C3 Bearings(x1) 6203 NR C3 Bearing(x2) Crank seals 17 x 40 x 7(x1) output shaft seal 22 x 40 x 7

Puch E50 Engine Hardware Set

Hardware set for your Puch E50 powered mopeds like the Maxi, etc. Zinc plating for rust resistance. Package includes:  (8) M6 x 31mm, (5) M6 x 55mm engine case allen bolts (4) M6 x...

Puch E50 Kick Start Stock Engine Complete Gasket kit

Stock 50cc Gasket gasket kit specifically for Puch E50 kick start engines found on the Korado and Magnum X. Will work on mopeds like the Maxi, Pinto, Swinger, Dart, Cobra, Freespirit, Korado and...

Puch E50 Kickstart Clutch Cover - Euro Models

Kickstart clutch cover for European Puch E50 powered kickstart mopeds. Will not work on US E50 models without modifications. We are working on getting the needed parts to assist. Bare, includes...

Puch E50 Kickstart Clutch Cover Gasket - Euro Models

Kickstart clutch cover gasket for European Puch E50 powered kickstart mopeds. Will not work on US E50 models.Recommended Accessories:Clutch Cover  Oil...

Puch E50 Kickstart Gear Circlip - 16mm

16mm Circlip/snap ring. Mounts on the kick start gear shaft inside the clutch cover on Puch E50 powered kickstart mopeds. Will not work on US E50 models without modifications. We are...

Puch E50 Kickstart Lever Return Spring - Euro Models

Replacement return spring for European Puch E50 powered kickstart mopeds. Will not work on US E50 models.Recommended Accessories:Clutch Cover  Oil Seals  

Puch E50 Kickstart Return Spring Guide - Plastic

Return spring guide for European Puch E50 powered kickstart mopeds. Will not work on US E50 models without modifications. We are working on getting the needed parts to assist...

Puch E50 Oil Seal Set - 3 Seals

Quality replacement 3 piece oil seal set. You get (2) crankshaft seals and (1) for output shaft.Includes:(x2) Crank seals 17 x 40 x 7(x1) output shaft seal 22 x 40 x 7

Puch E50 Racing Crankshaft - Unstuffed

Unstuffed racing crankshaft from for Puch E50 powered mopeds. Models like Maxi, Freespirit, Pinto, etc.Recommended Accessories:E50 Seals

Puch E50 Transmission Fluid Fill bolt - M10 x 1.5

Replacement transmission fill bolt for Puch E50 powered mopeds. Dimensions:M10 x 1.5mm Threading15mm overall length14mm wide head

Puch Exhaust Gasket, Header to Baffle - 26id x 32od

Replacement exhaust gasket for Puch mopeds with stock 2 piece exhaust. This is the header to baffle gasket.  Dimensions:26mm  ID32mm OD2mm Thick