Engine

Puch ZA50 Clutch Cover Gasket - Euro Spec

Top quality Puch ZA50 clutch cover gasket. This version is slightly different and for rarer Euro Spec models. Some have been imported into the U.S.   Most likely you will need this one HERE.   Made by the good boys and girls at BAC...

Puch ZA50 Clutch Cover Gasket

Top quality Puch ZA50 clutch cover gasket. Made by the good boys and girls at BAC. Recommended Accessories: Transmission Oil  

Stock Motobecane Cady Moby x1 Cylinder Kit - 39mm 50cc

Nice stock cast iron replacement cylinder for your Motobecane M1 / C1 Isodyne powered moped.  It is a high quality cast aluminum cylinder.  .    Does not fit any other U.S. model besides the  CADY, X1, M1, Moby 7 moped.. The AV7...

SKF 6204 C4 Crankshaft Bearing

SKF 6204 C4. high quality crankshaft bearing. 20 x 47 x 14 Fits: Right side Honda MB5, MB50, MT50 and similar Euro models.  Also for various Derbi, Peugeot models. Plus both sides of the infamous Suzuki FA50 engines. Recommended...

Honda MB5 Left Crankshaft Bearing - 62/22 C3

NTN quality replacement crankshaft bearing for left side  . Fits: Honda MB5, MB50, MT50 and similar Euro models.   Recommended Accessories: MB5 Crankshaft  MB5 Engine Gasket Kit

Sachs 505 Engine Seal Kit

Engine seal kit for Sachs 504 505 engines typically found on the Hercules, KTM Foxi and other mopeds with the Sachs engine.  Comes with everything shown. 1x 15x35x7 / 4 (flywheel side crankshaft seal) 1x 15x32x5.5  (output shaft...

6203 C3 Crankshaft Bearings - NTN

NTN quality bearing for crankshafts for many mopeds like the E50 powered Maxi, Newport, freespirit, pinto, etc.  Garrelli NOI / VIP, Tomos A35/ A55, Some Peugeot, Morini and others. Also used on other parts of engines and transmission such as the...

Morini M1 43.5mm 60cc Airsal Cylinder Kit

Airsal cylinder kit for the Morini M1  60cc size will increase power but remain reliable with proper jettingIncludes: everything shown. No gaskets. Known to fit the following models.  Pre 1985 engines will require case boring to fit the larger...

Honda MB5 Crankshaft Bearing and Engine Seal Set

Replacement crankshaft bearing and engine seals set.   Comes with two crank bearings and seals shown. Fits: Honda MB5, MB50, MT50 and similar Euro models Recommended Accessories: MB5 Crankshaft  MB5 Engine Gasket Kit

Honda MB5 Crankshaft - Jasil

Top quality replacement. Lighter weight and reinforced allows for higher RPMs and will make your engine more reliable with larger cc cylinder kits.    Includes wrist pin bearing. Made in Portugal by JASIL / Top Racing   Fits: Honda...

Puch Flywheel Cover with Emblem and Logo - Black

Flywheel cover for Puch mopeds. Now in black.   Works on E50 or ZA50 engine such as the Maxi, Magnum, Newport, Korado, Dart, Swinger, Pinto, Freespirit, Kromag, MKII, Cobra Replaces Puch Part # 3497100342 Comes with sticker for inside...

Motobecane Cady Engine Gasket Set

Replacement engine gasket set for Motobecane Cady, MobyX and other makes/ models that came with the M1 / M3 Isodyne style engines. Like G.A.C. Does not fit the typical AV7 or AV10 engines. Comes with everything shown.      

Tomos A55 70cc Airsal Replacement Cylinder Kit - No Head

Cylinder Kit only. No head..   Replacement Tomos A55 Airsal 70cc Cylinder.   Perfect if  your old one suffers a miss and implodes. Or get kinky and use it on something exotic other than a Tomos. Puch.   Comes with everything...

Motobecane AV10 47mm AIrsal Cylinder Kit

Quality Airsal 74cc cylinder kit for your AV10 powered MBK / Motobecane moped. No gaskets included.  47mm of fun. 13mm wrist pin Includes:CylinderPistonRingsWrist pinCir clips Head Gasket, not shown. Airsal 02144847

Motobecane Seat Post and Expanding Bolt

Seat post and expanding bolt for Motobecane mopeds.   For use with any clamp on type bicycle seat mounts.   Frame insert section 25.5mm Seat Mount 21.5mm

Motobecane Cady 38.95mm Stock 50cc Piston Kit

Perfect replacement for your worn or damaged piston for your Motobecane Cady.   Does not work with any other Motobecane engine. No AV7 found on 40v,50v etc. No, No, No. Cady ONLY> Comes with everything shown. Piston, rings, wrist pin,...

Piaggio Polini Speed Engine Case - Piaggio Points Ignition or Kinetic CDI

  Polini speed racing engine case for the ultimate tuning adventure.     Large opening ready to drop up to a 46mm cylinder in. For Racers Only! ;). Test and Tune. Eat, sleep, repeat.  Test and Tune. Eat, sleep, repeat...

Airsal Piston Ring - 47mm x 1mm GI

Airsal replacement piston ring. 47mm x 1.5 G.I. Type Replacement for several 47mm  Cylinder Kits. Airsal, Athena, Gilardoni, Metrakit, Parmakit. For  Derbi, Motobecane and Puch.  

Honda NSR50, NS-1, NS50f Complete Gasket Set

Complete Stock(50cc) gasket set to rebuild your NSR50, NS-1, NS50F, MBX, or similar Honda 2 stroke liquid cooled engine. Comes with everything shown.  Head, Base, Center Case,  Clutch Cover, Exhaust, Intake .  

Omega Motobecane AV7 - AV10 Full Circle Crankshaft - Reverse Thread

Performance crankshaft from the performance legends of Omega. Full circle for reed valve type Motobeane engines,  stock AV10 or performance AV7 cases.Comes with wrist pin bearing. Reverse, left hand thread ignition side / flywheel nut...

Tomos A35 / A55 Clutch Cover Gasket - 11 Hole .22MM

   Tomos A35 / A55 clutch cover gasket, for 2003 and on A35 / A55 mopeds only.     Thickness is 0.22mm   11 Hole Version. Count yours.  If it only 9  then this one is not for you.    Replaces Tomos...

Puch MS50 / MV50, Sears Allstate Top End Gasket Set 1

Top end Gasket set for MS and MV50 / Sears Allstate mopeds.  Base, head and exhaust 38mm stock size

Piaggio Vespa Performance Crankshaft - 12mm Pin

Performance Vespa Piaggio Kinetic crank. Fits Citta, bravo, ciao, si. 12mm Wrist pin.    Attention! Check and measure if you need a 10mm or 12mm version before buying.

Polini Motobecane AV10 Engine Race Case Set

 Polini Motobecane AV10 complete engine case kit.  Reinforced Bearings, seals, two intakes, hardware and gaskets (not shown). Intake is Dealers choice.  Dellorto 19mm SHA or  24mm PHBG type mounting diameters. M7 x 1.00 Studs...

Polini Motobecane 46mm Cylinder Head W Decomp

Polini  Motobecane AV7 70c cylinder head w/decompressor hole - 46mm Larger fins for extra cooling.  Works well with 70cc-74cc  cylinders. Polini# 211.0202 

Puch Airsal 47mm Cylinder Kit - Angled Exhaust Port

Adaptable with Puch based mopeds with E50 or ZA50 engines.  47mm will only fit with case grinding and adding material to mate the large port transfers.  Only recommended for über advanced tuners.  If welding, boring, case...

Piaggio / Kinetic 38.2mm Budget Cylinder Kit - 12mm Wrist Pin

38.2mm budget cast iron cylinder kit with 12mm wrist pin,  Perfect replacement to get your vintage moped up and running again.This will work on all 12mm Piaggio, Vespa, and Kinetic mopeds.   Gaskets may or may not come with the kit...

DMP Piaggio Cylinder Head - 41mm

41mm Cylinder Head with decompression hole. For Vespa / Piaggio / Kinetic mopeds,  Ciao, Bravo, Grande, Si, Boxer, TFR. with 41mm cylinders    

Motobecane Recoil Pull Start Kit - AV7

Recoil pull start assembly for Motobecane AV7 engines with reverse thread crankshafts. Includes:Pull start assemblyBack plateFace plateClutch plateHardware

Puch Athena 45mm 70cc Reed Cylinder Kit- Amal Intake

Top quality Athena 45mm cylinder kit for E50 engines found on various Puch mopeds like the maxi, Newport, magnum, pinto, swinger, Murray and many others.  This is the reed intake version not a piston port.  70cc of Italian power! This...

Puch 74cc Italkit / Gilardoni 47mm Gasket Set

Puch Gilardoni 74cc cylinder replacement gasket set.  *Includes Everything Shown Made by Italkit

Puch / Tomos 50cc 38mm Cylinder Head

This replacement original style 38mm, 50cc high cylinder head works with all ZA50 and E50 engines found on various Puch engine mopeds like the maxi, magnum, swinger, pinto, freespirit and many others.  Also can be used  on all Tomos A3, A35 and...

Vespa Piaggio Polini Engine Case - CDI Ignition

  Polini speed racing engine case for the ultimate tuning adventure.   Supplied with 13mm intake and hardware ready for a 13.13  Dellorto carburetor.   Large opening ready to drop up to a 46mm cylinder in. For Racers...

Puch Front Sprocket - 14 Tooth

Quality 14 tooth front sprocket for Puch Maxi. Will fit the E50 and ZA50 engines. 

Piaggio Vespa Kinetic 38.4mm DR Piston Kit - 10mm Wrist Pin

38.4mm DR Piston Kit with 10mm wrist pin for Vespa piaggio and Kinetic mopeds. For use with DR Cylinder Kits. Original size of  Ciao and other Piaggio / Kinetic mopeds is 38.2mm

Puch E50 4 Bearings Set - BAC

Top Quality bearings set for rebuilding Puch E50 engines. Found on many mopeds like the  Maxi, Newport, Pinto, Swinger, Dart, etc. Includes:(x3) 6203 C3 Bearings(x1) 6203 NR C3 Bearing Recommended Accessories:  3 Seal Set Complete...

Puch High Compression Cylinder Head- 45mm /70cc

This 70cc 45mm high compression cylinder head works with all ZA50 and E50 engines found on various Puch engine mopeds like the maxi, magnum, swinger, pinto, freespirit and many others.  Also fits on Tomos Should be paired with 70cc cylinder...

Vespa Piaggio Kinetic 43mm Polini Cylinder Kit "Racing Edition" w/ 12mm wrist pin

Top quality 43mm Polini Racing Edition cylinder kit for your Piaggio Vespa. Includes everything you see, 12mm wrist pin. Not sure what size pin you have, take out your piston and measuring before ordering or be sorry later. Italian made and ready to...

Piaggio Vespa Kinetic 38.4mm Stock Piston Kit - 10mm Wrist Pin

Replacement 38.4mm piston kit with 10mm wrist pin. Works with Kinetic and Vespa Piaggio mopeds.  Attention!  You must remove your cylinder and see what size wrist pin you have.  10mm or 12mm as they came with both.  Or otherwise it...

Puch Rito Stuffed Performance Crankshaft - E50

Racing crankshaft from Rito for Puch E50 powered mopeds. Models like Maxi, Freespirit, Pinto, etc.Recommended Accessories:Important 6203 C3 BearingE50 Seals